Question - Ive recently started trying to use kiss to pull with a warrior, not quite there

[dealings]

The warr uses nav, pulls a mob w ranged item (bow and arrow)
then stands there (does not return to camp)
I would love to make it so he tries to return immediatley after launching arrow

Im guessing there is a setting in ini I am not setting up right
also what how is this used

[PullAdvanced]
PullLocsOn=1

this is what I have for pull section (using v 12 btw)

[Pull]
PullWith=Velium Threaded Bow|Ethereal Arrow
PullMeleeStick=0
MaxRadius=450
MaxZRange=10
UseWayPointZ=0
PullWait=30
PullRadiusToUse=100
PullRoleToggle=0
ChainPull=0
ChainPullHP=0
PullPause=30|2
PullLevel=0|0
PullArcWidth=0
PullOnReturn=1

 

[Smokeybear72]

The warr uses nav, pulls a mob w ranged item (bow and arrow)
then stands there (does not return to camp)
I would love to make it so he tries to return immediatley after launching arrow

Im guessing there is a setting in ini I am not setting up right
also what how is this used

[PullAdvanced]
PullLocsOn=1

this is what I have for pull section (using v 12 btw)

[Pull]
PullWith=Velium Threaded Bow|Ethereal Arrow
PullMeleeStick=0
MaxRadius=450
MaxZRange=10 ----------- Change this to 250 or higher( I dont know of any zones that are this flat)
UseWayPointZ=0
PullWait=30    ------------ Change this to 5 or 10 ( waiting 30 seconds between pulls ?? Seems very long IMO )
PullRadiusToUse=100   
PullRoleToggle=0
ChainPull=0
ChainPullHP=0
PullPause=30|2
PullLevel=0|0
PullArcWidth=0                 ----- 0 pull arc ?     Maybe its the same as 360, but I might be something to consider as you get more advanced so you can choose which direction to pull
PullOnReturn=1

As far as returning to camp:

What is your General settings? Camp radius, CampRadiusExceed ? that stuff

 

[dealings]

not sure what Chaseassist or chasedistance mean but this is what I have

Role=PullerTank
CampRadius=45
CampRadiusExceed=800
ReturnToCamp=1
ChaseAssist=0
ChaseDistance=25

 

[Robban]

The warr uses nav, pulls a mob w ranged item (bow and arrow)
then stands there (does not return to camp)
I would love to make it so he tries to return immediatley after launching arrow

Im guessing there is a setting in ini I am not setting up right
also what how is this used

[PullAdvanced]
PullLocsOn=1

this is what I have for pull section (using v 12 btw)

[Pull]
PullWith=Velium Threaded Bow|Ethereal Arrow
PullMeleeStick=0
MaxRadius=450
MaxZRange=10
UseWayPointZ=0
PullWait=30
PullRadiusToUse=100
PullRoleToggle=0
ChainPull=0
ChainPullHP=0
PullPause=30|2
PullLevel=0|0
PullArcWidth=0
PullOnReturn=1

PullLocsOn

0

0/1

Turn on or off using the PullLocs areas in the KissAssist_Info.ini file for the zone. For more information see the KissAssist_info.ini Setup Instructions.

turn that off

 

[Robban]

The warr uses nav, pulls a mob w ranged item (bow and arrow)
then stands there (does not return to camp)
I would love to make it so he tries to return immediatley after launching arrow

Im guessing there is a setting in ini I am not setting up right
also what how is this used

[PullAdvanced]
PullLocsOn=1

this is what I have for pull section (using v 12 btw)

[Pull]
PullWith=Velium Threaded Bow|Ethereal Arrow
PullMeleeStick=0
MaxRadius=450
MaxZRange=10
UseWayPointZ=0
PullWait=30
PullRadiusToUse=100
PullRoleToggle=0
ChainPull=0
ChainPullHP=0
PullPause=30|2
PullLevel=0|0
PullArcWidth=0
PullOnReturn=1

have you looked in here?

KissAssist - Read📖Guides

www.redguides.com

 

[dealings]

i had book marked an older guide, replacing it now w that one

 

[RYN227]

When I tried Kiss for pulling I did notice my puller would fire an arrow at the mob then hang around for a couple seconds just standing there. This made me pretty nervous and in Wall of Slaughter where all mobs run at SoW speed, it got me a few times. However, he always returned to camp though.

 

[dealings]

would be nice to tighten up that part of pulling, not sure why its not doing even that for me now
It do that once or twice b4 now he pulls then decides f it this is a good spot to fight

 

[ctaylor22]

Does the mobs he is pulling show up in the XTended target window when aggroed? There are multiple things that trigger the puller to return to camp. But here are the bassic steps 1 - Do I have aggro? 2 - Then return to camp. 3 - Is ReturnToCamp turned OFF? Then Ignore step 2.

So either ReturnToCamp is turned off, or the puller is NOT seeing the mob show up in the Xtarget window. Here is something you can try. When this happens just go edit the pullers ini file and look in the [General] section. Look at the what XTSlot is set to. OK now is the XTarget entry, that XTSlot is set to, an autohater entry?

 

[dealings]

the problem was having xtar 1 set as grp assist target instead of auto
once I set it back to auto it resolved the problem of not returning to camp after trying to pull a mob
ty vm