Question - PULL Mobs/Ignore Mobs in Info.ini

[KS1980]

Question: i hardly use kissassist to pull but i just tried this and for some reason it will pull the ph'ers but not the named. the named will follow the pheres but it will just ignore pulling the named. i read and followed the info.ini instcutions but to no avail am i being succesfful.

so in FFP i have a soot-specked hawk and Fowl Matriarch in my list to pull

[Firefall Pass]
MezImmune=List up to 10 mobs. Use full names i.e. a green snake,a blue tiger,a wide eye ooze or NULL
AAMezImmune=0
MobsToPull=a soot-specked hawk,Fowl Matriarch,
MobsToIgnore=List up to 25 mobs. Use full names i.e. a green snake,a blue tiger,a wide eye ooze or NULL
MobsToBurn=List up to 10 mobs. Use full names i.e. Beget Cube,Helias,Raze or NULL
PullPath=Place holder for path file. Not yet impletmented.
PullLocsHelp=Y,X|Range. Ignore mobs in this area
PullLocs1=0
PullLocs2=0
PullLocs3=0
PullLocs4=0
PullLocs5=0

Even if Fowl Matriarch is directly in front of me, he just bypasses this named and pulls the ph instead. ive tried to repostion myself but the outcome is the ame. the information file says to place a # in front og ther name but that too doesnt work. can anyone assist me ? thanks

 

[Robban]

Question: i hardly use kissassist to pull but i just tried this and for some reason it will pull the ph'ers but not the named. the named will follow the pheres but it will just ignore pulling the named. i read and followed the info.ini instcutions but to no avail am i being succesfful.

so in FFP i have a soot-specked hawk and Fowl Matriarch in my list to pull

[Firefall Pass]
MezImmune=List up to 10 mobs. Use full names i.e. a green snake,a blue tiger,a wide eye ooze or NULL
AAMezImmune=0
MobsToPull=a soot-specked hawk,Fowl Matriarch,
MobsToIgnore=List up to 25 mobs. Use full names i.e. a green snake,a blue tiger,a wide eye ooze or NULL
MobsToBurn=List up to 10 mobs. Use full names i.e. Beget Cube,Helias,Raze or NULL
PullPath=Place holder for path file. Not yet impletmented.
PullLocsHelp=Y,X|Range. Ignore mobs in this area
PullLocs1=0
PullLocs2=0
PullLocs3=0
PullLocs4=0
PullLocs5=0

Even if Fowl Matriarch is directly in front of me, he just bypasses this named and pulls the ph instead. ive tried to repostion myself but the outcome is the ame. the information file says to place a # in front og ther name but that too doesnt work. can anyone assist me ? thanks

could check your char ini for
PullLevel=0|0

maybe you have set a lvl restriction there?

 

[timmy]

change Fowl Matriarch to fowl*

 

[KS1980]

change Fowl Matriarch to fowl*

does this look correct?

MobsToPull=a soot-specked hawk,Fowl*,
and thx

 

[timmy]

yes, maybe. at least, I think. ha! I’m not sure if Fowl should be capitalized. i know with certainty that fowl* (and rock* for Rock Lobber) work. And I only tried the lower case because of this post and that’s what they used (the lower case and the *) with success. That post is interesting w/ some of the details about how KA is doing “stuff” behind the scenes. And in the case of the Rock Lobber, when KA does pull it (with rock*), it shows in the MQ window as #Rock Lobber. But if you check /who info, the # isn’t visible. And KA won’t pull it if you have it in your ini as #Rock Lobber. I am guessing the fowl is the same but I wasn’t paying as close of attention to the MQ window on the bird pull. But again, I’m 100 percent certain fowl* will pull it and if the * is just doing partial matches, it seems reasonable that Fowl* would work as well since the bird has that exact capitalization in its name.

 

[KS1980]

thx, i got confused as the instrions states to place the # but ill give the * a try