• IS THIS SITE UGLY? Click "RG3" at the very bottom-left of this page to change it. To dismiss this notice, click the X --->

Question - Issues with Mq2dpsadv and mq2advnav

dorimor

New member
Joined
Jul 19, 2015
Likes
0
RedCents
106¢
#1
hello folks ,


I seem to only be able to see the single characters DPS on Dpsadv window ingame im sure its just a settings thing but iv tried various combos and cant get it to work was wondering if someone could just post settings up for me please.


Also having some issues with using melee classes on mq2advnav with the range not being enough when i run into a mob the melee character starts trying to dart to the target to attack and dart back to its follow target ..... so how do i extend mq2advnavs follow distance to im guessing 25 as that is the correct setting for chase assist in kiss ? but chase assist does not seem to break sitting meds or anything like that so would prefer to use mq2
 
Joined
Dec 17, 2016
Likes
4
RedCents
100¢
#2
For the DPS it sounds as though you have filtered out other people's hits. Each one of your characters needs to be able to see each other's hits to see their dps. Same for spells. Check your EQ filtering under options.

Not sore on the other issue.


Sent from my iPhone using Tapatalk
 

Maskoi

So old and salty he grew scales
Moderator
Joined
Sep 28, 2005
Likes
488
RedCents
66,344¢
#3
MQ2AdvPath or MQ2nav? They are separate plugins
 
Joined
Dec 17, 2016
Likes
4
RedCents
100¢
#4
MQ2AdvPath or MQ2nav? They are separate plugins
I'm not sure it's either. I run into the same issue. I have a ranger that is set to pull with bow. If it happens that the mob is fairly close when he goes to pull. (Closer than bow range) he will just stick to the mob and chase it. All while you see that you are to close for this ranged item. I'm setup to pull from a radius and no paths. I'm in an area that has KOS and non KOS mobs. Luckily the mob on this instance was a KOS and once aggro was engaged the ranger pulled it back into camp.


This only happened once to my knowledge.


Sent from my iPhone using Tapatalk
 

Maskoi

So old and salty he grew scales
Moderator
Joined
Sep 28, 2005
Likes
488
RedCents
66,344¢
#5
Not what I meant. He said mq2advnav. that's not a plugin
 

dorimor

New member
Joined
Jul 19, 2015
Likes
0
RedCents
106¢
#6
im sorry its is MQ2advpath im having the issue with i would like to increase the leash distance from main toon so when i stop running to kill somthing i dont have to turn off follow
 

Maskoi

So old and salty he grew scales
Moderator
Joined
Sep 28, 2005
Likes
488
RedCents
66,344¢
#7
What exactly is it you are trying do. The MQ2advpath pull only supports run to mob, tag, run back to camp.
 

dorimor

New member
Joined
Jul 19, 2015
Likes
0
RedCents
106¢
#8
i Want the alt toons to follow the tank as i run him around but be at a distance that melee can engage. At The moment they engage the mobs with kissasist try to run around back of mob then end up running back to tank because of leash range
 

Maskoi

So old and salty he grew scales
Moderator
Joined
Sep 28, 2005
Likes
488
RedCents
66,344¢
#9
Kiss can't do this using MQ2advpath. IT only support pulling back to camp.

You should be able to follow the tank normally with your toons and attack the follow again.

Are you using the /chaseon command to follow your tank?
 

dorimor

New member
Joined
Jul 19, 2015
Likes
0
RedCents
106¢
#10
i am but it seems very slow to pick up character that have chosen to med after combat and in some cases it leave the character behind if im useing bard speed
 

Maskoi

So old and salty he grew scales
Moderator
Joined
Sep 28, 2005
Likes
488
RedCents
66,344¢
#11
I have it on my list to strengthen the chase routines. I want the toon to get up and follow again from medding, stop casting buffs, etc if tank gets a certain distance away.
 
Joined
Mar 31, 2018
Likes
6
RedCents
61¢
#13
For the DPS it sounds as though you have filtered out other people's hits. Each one of your characters needs to be able to see each other's hits to see their dps. Same for spells. Check your EQ filtering under options.

Not sore on the other issue.


Sent from my iPhone using Tapatalk
ok checked my filters and none of my other toons are showing dps in my main toons window,,,,what do i do?
 
Joined
Dec 24, 2017
Likes
193
RedCents
1,357¢
#15
I have it on my list to strengthen the chase routines. I want the toon to get up and follow again from medding, stop casting buffs, etc if tank gets a certain distance away.
Was curious if you ever got around to altering the chase routine. If so, is there away to change the distance a tank has to be from the tank before they drop what they are doing and follow? My mage is so stupid, I just want to kill him as he is always lagging behind.
 

Maskoi

So old and salty he grew scales
Moderator
Joined
Sep 28, 2005
Likes
488
RedCents
66,344¢
#16
I did. it will be released tomorrow in 11.010 beta
 
Top