Problem - Auto attack when targeting

[krentzn]

Version of KissAssist.mac?

12.001

When did your problem start?

now

Character Role?

1. Tank

What class is having this issue?

1. Shadow Knight

How often does this issue occur?

Always

Can you reproduce the issue?

yes everytime I target something.

Help please, everytime I target something (leftclick) my auto attack turns on. I'm running an SK as tank and using kissassist. Not sure if I missed something in the ini or what but I'm trying to buy spells and i keep attacking the vender.

 

[lilwizzie]

try using the EQ command /assist off

 

[Hylander]

Change AssistAt from 100 to 99

 

[krentzn]

Change AssistAt from 100 to 99

assist is set to 95

 

[krentzn]

try using the EQ command /assist off

nope still auto attacking on targeting

 

[AmericanNero]

It's an issue with vanilla KA12. What I normally do is /mqp while talking to merchants / npcs.

 

[ctaylor22]

If your trying to target a mob you don't want attacked, you should pause the macro. If you are using the ambush tag on any entries in your DPS section, then you need to use a condition that does a check to do the entry or not. Ambush tag entries ignore the AssistAt value.

 

[dpanaben]

If you are using the ambush tag on any entries in your DPS section, then you need to use a condition that does a check to do the entry or not. Ambush tag entries ignore the AssistAt value.

This is really helpful..!

 

[Zebadiah]

Has this been fixed or do I have to run all my characters that use KissAssist 12 on pause. This is what is happing ex: Ranger uses S camo and tries to go by a mob and attacks it dropping camo. Any mob or npc that get close he attacks (I don't have to target for him to attack.) When I target a mob to shoot with bow and arrow. He insteads runs up and smack it. I have to be real far away to be able to shoot. I am looking at going back to KissAssist 11.

 

[ctaylor22]

The range for ignoring your ranged weapon and running after the mob is less than 30. If you see the "to far" message getting spammed, then that will also trigger him to run towards the mob. He shouldn't be attacking any mob NOT on XTarget, but if your using AE debuffs to control aggro, you could be grabbing aggro from friendly mobs in the area.

 

[Zebadiah]

Dose not answer the question. Has the autotarget been fixed in KissAssist 12? With character (using KissAssist 12) targets a merchant or quest npc the character attacks what was targeted. Now its not bad when its a mob you want to kill or one that you run by but its annoying when you have to wait for the quest npc to respawn. So you start running around with pause on and then unpause to fight something then pause again.

Zeb

 

[ctaylor22]

Did you add the NPC to the ignore list? Do you have TargetSwitching Turned on? Kiss does not turn on auto attack. kiss uses the command /attack on or /attack off.

 

[Hulkman]

I think the problem is , you need to turn off pull with Melee stick .

Use pull with a spell example:
[Pull]
PullWith=Burning Ash
PullMeleeStick=0
MaxRadius=500
MaxZRange=90

 

[wymranar]

I have also run into this problem. I think I first noticed it in ToV so maybe it started with ka12.

 

[Hulkman]

I had this problem as well with my Shadow knight.

I unequipped my weapons and reloaded Red Guides and then placed weapons back on toon and it did the trick.

Have yourself targeted when doing this

 

[deathlock]

This typically happened to me if I wasn't in a group. I have never had it happen when I was grouped. I haven't tried it solo in awhile.

 

[wymranar]

I think one npc who is affected by this is crusader vratek or whatever his name is. The guy that gives the earring quest, I think I remember pausing my toons because this had happened before and he fought back