Question - Kissassist info.ini

[KS1980]

Hello, ive been reading up on the kissassist.com information for kissassist. The question i have pertains to the info.ini section. In this section it clearly states this:

Note: Mobs that names start with a #. You must include the # in the name for MobsToPull, MobsToIgnore.

Sample KissAssist_Info.ini file

[cityofbronze]
MobsToPull=grendlaen,braxi,selyrah,oashim,bloodclaw,strangleweed
MobsToIgnore=a sentry stone,Leaf Pile,Tyzen,Faltar,A Rabid Selyrah
MobsToBurn=List up to 10 mobs. Use full names i.e. Deathsqueak,A_Raging_Braxi,Guggles or NULL
MezImmune=List up to 10 mobs. Use full names i.e. a green snake,a blue tiger,a wide eye ooze or NULL
PullLocsHelp=Y,X|Range
PullLocs1=0
PullLocs2=0
PullLocs3=0
PullLocs4=0
PullLocs5=0

So inregards to placing a # in front of the Named name under MobsToPull, can someone give me a clearer example? Currently i have it set to *** MobsToPull=#Rumblecrush,a hefty stone guardian,a massive stone guardian, *** this will pull the 2 other mobs but if Rumblecrush is up it will be ignored and not pulled.

Thanks.

 

[Sifter228]

#=Stone
so "a stone guardian" must have the "a" before it.

[Valley of Lunanyn]
MezImmune=List up to 10 mobs. Use full names i.e. a green snake,a blue tiger,a wide eye ooze or NULL
MobsToPull=List up to 25 mobs. Use full names i.e. a green snake,a blue tiger,a wide eye ooze or ALL for all mobs
MobsToIgnore=a worn sentry stone,Geirdan Ath,Hemot Talas
MobsToBurn=an angry mob leader

 

[KS1980]

Thanjs for your r

#=Stone
so "a stone guardian" must have the "a" before it.

[Valley of Lunanyn]
MezImmune=List up to 10 mobs. Use full names i.e. a green snake,a blue tiger,a wide eye ooze or NULL
MobsToPull=List up to 25 mobs. Use full names i.e. a green snake,a blue tiger,a wide eye ooze or ALL for all mobs
MobsToIgnore=a worn sentry stone,Geirdan Ath,Hemot Ta

#=Stone
so "a stone guardian" must have the "a" before it.

[Valley of Lunanyn]
MezImmune=List up to 10 mobs. Use full names i.e. a green snake,a blue tiger,a wide eye ooze or NULL
MobsToPull=List up to 25 mobs. Use full names i.e. a green snake,a blue tiger,a wide eye ooze or ALL for all mobs
MobsToIgnore=a worn sentry stone,Geirdan Ath,Hemot Talas
MobsToBurn=an angry mob leader

There are 2 types of guardians. Which are 'a hefty stone guardian' and 'a massive stone guardian' both of which are not named. Kissassist will pull these mobs with no question. The issue im having is it will not pull RUMBLECRUSH. The settings i have is *** MobsToPull=#Rumblecrush,a hefty stone guardian,a massive stone guardian, *** and according to the kissassist info webpage it says i must include the # in the name which i did which still doesnt work. So i was just asking if i can get a clearer example onthe usage of utilizing tbe # in the name.

So im not sure if im understanding the usage of entering an actuql named name under the MobsToPull section or if im just totally comfused. I can enter all other mobs around thism camp but if a named spawns it wont pull it.

Thanks again.

 

[Sifter228]

Do not put # in front of anything.

 

[KS1980]

I remove the # and it just does the same thing. It Just ignores Rumblecrush. Which is why I’m confused on the kissassist.com write up section where it says:

“ Note: Mobs that names start with a #. You must include the # in the name for MobsToPull, MobsToIgnore. “

Am I missing something here in this section. I tried other zones with other named names and it just won’t pull any named at all even if I listed it on the MobsToPull section.

Thanks.

 

[Sifter228]

Whats your pull level setting?

PullLevel=100|123

 

[KS1980]

100 130

I even went to a lower zone in COV and still ignores a named. I’m just unsure if I’m actually inputting the correct format. Which is why I was asking if I could get an example of the setting where it states:

“ Note: Mobs that names start with a #. You must include the # in the name for MobsToPull, MobsToIgnore. “

Also something to add is if I just remove the mobs under MobsToPull and leave that blank, it will pull the named if it spawns.

Thanks again

 

[Sifter228]

100 130

I even went to a lower zone in COV and still ignores a named. I’m just unsure if I’m actually inputting the correct format. Which is why I was asking if I could get an example of the setting where it states:

“ Note: Mobs that names start with a #. You must include the # in the name for MobsToPull, MobsToIgnore. “

Thanks again

MobsToPull=Rumblecrush,a hefty stone guardian,a massive stone guardian
This doesn't work?

 

[KS1980]

No. It just ignores it. Tbh so far since this thread it’s ignored all named mobs. But like I said if I don’t enter anything in the MobsToPull section, it will defiantly pull the named provided it’s within pulling distance

 

[B_I_G__D_A_D_D_Y]

I just put the name in both ways #Rumblecrush,Rumblecrush,a hefty stone guardian